LPAR Movement from One Frame to Another

Steps for migrating LPAR from ONE Frame to Another IBM Frame

1.Have Storage zone the LPARs disk to the new HBA(s). Also have them add an additional 40GB drive for the new boot disk. By doing this we have a back out to the old boot disk on the old frame.

2. Collect data from the current LPAR:

a. Network information – Write down IP and ipv4 alias(s) for each interface

b. Run “oslevel –r” - will need this when setting up NIM for the mksysb recovery

c. Is the LPAR running AIO, if so will need to configure after the mksysb recovery

d. Run “lspv”, save this output, contains volume group and PVID information

e. Any other customizations you deem neccessary


3. create mksysb backup of this LPAR

4. Reconfigure the NIM machine for this LPAR, with new Ethernet MAC address. Foolproof method is to remove the machine and re-create it.

5. In NIM, configure the LPAR for a mksysb recovery. Select the appropriate SPOT and LPP Source, base on “oslevel –r” data collected in step 2.

6. Shut down the LPAR on the old frame (Halt the LPAR)

7. Move network cables, fibre cables, disk, zoning

8. if needed, to the LPAR on the new frame

9. On the HMC, bring up the LPAR on the new frame in SMS mode and select a network boot. Verify SMS profile has only a single HBA (if Clarrion attached, zoned to a single SP), otherwise the recovery will fail with a 554.

10. Follow prompts for building a new OS. Select the new 40GB drive for the boot disk (use lspv info collected in Step 2 to identify the correct 40GB drive). Leave defaults for remaining questions NO (shrink file systems, recover devices, and import volume groups).

11. After the LPAR has booted, from the console (the network interface may be down):

a. lspv Note the hdisk# of the bootdisk

b. bootlist –m normal –o Verify boot list is set – if not, set it

bootlist –m normal –o hdisk#

c. ifconfig en0 down If interface got configured, down it

d. ifconfig en0 detach and remove it


e. lsdev –Cc adapter Note Ethernet interfaces (ex. ent0, ent1)

f. rmdev –dl Remove all en devices

g. rmdev –dl Remove all ent devices

h. cfgmgr Will rediscover the en/ent devices

i. chdev –l -a media_speed=100_Full_Duplex Set on each interface unless

running GIG, leave defaults


j. Configure the network interfaces and aliases Use info recorded from step 2 mktcpip –h -a -m -i -g -A no –t N/A –s

chdev –l en# -a alias4=,


k. Verify that the network is working.


12. If LPAR was running AIO (data collected in Step 2), verify it is running (smitty aio)

13. Check for any other customizations which may have been made on this LPAR

14. Vary on the volume groups, use the “lspv” data collected in Step 2 to identify by PVID a hdisk in each volume group. Run for each volume group:

a. importvg –y hdisk# Will vary on all hdisk in the volume group

b. varyonvg

c. mount all Verify mounts are good

15. Verify paging space is configured appropriately

a. lsps –a Look for Active and Auto set to yes

b. chps –ay pagingXX Run for each paging space, sets Auto

c. swapon /dev/pagingxx Run for each paging space, sets Active


16. Verify LPAR is running 64 bit

a. bootinfo –K If 64, you are good


b. ln –sf /usr/lib/boot/unix_64 /unix If 32, change to run 64 bit

c. ln –sf /usr/lib/boot/unix_64 /usr/lib/boot/unix

d. bosboot –ak /usr/lib/boot/unix_64


17. If LPAR has Power Path

a. Run “powermt config” Creates the powerpath0 device

b. Run “pprootdev on” Sets Power Path control of the boot disk

c. If Clariion, make configuration changes to enable SP failover


chdev -l powerpath0 -Pa QueueDepthAdj=1

chdev –l fcsX –Pa num_cmd_elems=2048 For each fiber adapter

chdev –l fscsiX –Pa fc_err_recov=fast_fail For each fiber adapter

d. Halt the LPAR

e. Activate the Normal profile If Sym/DMX – verify two HBA’s in profile

f. If Clarrion attached, have Storage add zone to 2nd SP

i. Run cfgmgr Configure the 2nd set of disk


g. Run “pprootdev fix” Put rootdisk pvid’s back on hdisk

h. lspv grep rootvg Get boot disk hdisk#

i. bootlist –m normal –o hdisk# hdisk# Set the boot list with both hdisk


20. From the HMC, remove the LPAR profile from the old frame

21. Pull cables from the old LPAR (Ethernet and fiber), deactivate patch panel ports

22. Update documentation, Server Master, AIX Hardware spreadsheet, Patch Panel spreadsheet

23. Return the old boot disk to storage.